Ascentia J40 CMOS Options Access: during a warm or cold boot. NOTE: Pressing + after the system boots allows the user to configure the the power management portion of setup. For access to all of the Setup fields, run during boot. User Interface: Change configuration menu - Move through configuration fields - Enter a Sub-Menu (not always available) - Change configuration - <+ / - / space bar> Help - Default Values - Last saved CMOS values - Exit Setup - Configuration Fields: Use the to choose the configuration menu. Main Menu Peripherals Menu Power Manager Menu Security Menu ***************************************************************************************************************************** [ MAIN MENU ] Date: Enter Date, Month, and Year. Time: Enter Hour, Minute, and Second in 24-hour format. Fixed Disk: Choose Auto to automatically configure an IDE type drive, User Define to choose hard disk type, or Disable for no hard drive. 32-bit I/O: Choose Enable to support 32-bit hard drive access, or Disable for 16-bit access. Boot Sequence: Choose A: First, C: First , or C: Only. Quick Boot: Choose Enable to bypass the setup prompt, post errors, floppy check, and summary screen. Choose Disable to for a complete POST at boot. Keyboard Clicks: Choose Enable or Disable. Cache Memory: Displays amount of cache memory detected; for reference only. Base Memory: Displays amount of base/conventional memory detected; for reference only. Extended Memory: Displays amount of extended memory detected; for reference only. [ PERIPHERALS ] Plug-and-Play Hardware: Choose Enable to have all peripherals set up automatically. or Disable to allow user to manually set the fields below. Serial Port: Choose 3F8 IRQ 4, 2F8 IRQ 3, 3E8 IRQ 4, 2E8 IRQ 3, or Disable. Parallel Port: Choose 3BC IRQ 7, 378 IRQ 7, 278 IRQ 5, or Disable. Parallel Mode: Choose Out Only, Bi-directional, EPP, or ECP. InfraRed: Choose 3F8 IRQ 4, 2F8 IRQ 3, 3E8 IRQ 4, 2E8 IRQ 3, or Disable. Modem Module: Choose 3F8 IRQ 4, 2F8 IRQ 3, 3E8 IRQ 4, 2E8 IRQ 3, or Disable. [ POWER MANAGER MENU ] Power Saving Mode: Choose Max, Mid, Min, Customize, or Disable. Standby Timeout: Choose Disable, 30 Sec, 1 Min or 5 Min. Available only if Power Saving Mode is set to "Customize". Suspend Timeout: Choose Disable, 1 Min, 5 Min or 20 Min. Available only if Power Saving Mode is set to "Customize". SmartSleep Timeout: Choose Disable, 5 Min, 10 Min or 20 Min. Available only if Power Saving Mode is set to "Customize". Cover Lid Switch: Choose LCD off or Suspend. Suspend Mode: Choose Suspend or SmartSleep. Power Switch: Choose Off or Suspend. Low Battery Activity: Choose Quiet, Beep, or Suspend. Resume on Modem Ring: Choose Enable or Disable. Resume on Schedule: Choose Enable or Disable. If enabled, enter the time for the system to resume. CPU Speed: Choose Fast, 50%, 25%, or 12%. HDD Timeout: Choose Disable, 15 Sec, 1 Min, or 5 Min LCD Timeout: Choose Disable, 30 Sec, 1 Min, or 5 Min Battery Status: Displays Charged, Discharged, Not Charged, Bad, or None; for reference only. [ SECURITY MENU ] Administrator Password is: Displays Disabled or Enabled; for reference only. User Password is: Displays Disabled or Enabled; for reference only. Set Administrator Password: Press to access the password entry screen. Password is entered and verified here. The password may be up to seven characters. The Administrator password allows full access to all Setup fields. To disable a password, press at this field, and then press at the next two prompts. Set User Password: Press to access the password entry screen. Password is entered and verified here. The password may be up to seven characters. The Administrator password must be enabled before a User password is allowed. The User password allows limited access to Setup fields. To disable a password, press at this field, and then press at the next two prompts. Backup Password: Put a blank, formatted diskette in the A: drive, and press to backup the password information to diskette. If a password is forgotten, boot the system. When you are prompted to enter the password, put the backup diskette in the floppy drive, and type "floppy" at the password prompt. Password on Boot / Resume: Choose Enable or Disable. Hard Disk Boot Sector: Choose Normal or Write Protected. Lock Keyboard: Choose Disable, 2 Min, 10 Min, or 30 Min. Lock Floppy Access: Choose Disable, User, or Supervisor. [ EXIT SYSTEM SETUP MENU ] Discard Changes & Exit: Changes are ignored, and the system reboots. Save Changes & Exit: Changes are saved to CMOS memory, and the system reboots. Get Default Values: All fields are loaded with factory default values. Load Previous Values: All fields are loaded with the last-saved configuration. Save Changes: All changes are saved to CMOS memory.